Akcije

Journal of Applied Engineering Science
kako citirati ovaj članak
podeli ovaj članak

Metrika

  • citati u SCIndeksu: 0
  • citati u CrossRef-u:0
  • citati u Google Scholaru:[]
  • posete u poslednjih 30 dana:6
  • preuzimanja u poslednjih 30 dana:6

Sadržaj

članak: 1 od 9  
Back povratak na rezultate
2021, vol. 19, br. 1, str. 252-257
Investigation of lightweight structural materials produced using aluminum scraps with cement mortar
(naslov ne postoji na srpskom)
aMustansiriyah University, Faculty of Engineering, Civil Engineering Department, Baghdad, Iraq
bMustansiriyah University, Faculty of Engineering, Water Resources Engineering Department, Baghdad, Iraq

e-adresadr.abdulqadernihad@uomustansiriyah.edu.iq
Ključne reči: aluminum scraps; compressive strength; fine aggregate; lightweight; sustainable
Sažetak
(ne postoji na srpskom)
A lot of environmental concerns are increasing day after day result in the raise of solid waste in large quantities in the world resulting from the demolition of buildings and various industrial and commercial activities. This research provides the possibility of reusing one of these wastes solid aluminum scrap (Als) by using it to produce a modified type of cement mortar. The research focuses on the mechanical behavior of the new cement mortar type obtained by adding aluminum scrap by different percentages (1%, 2%, 3%, 4%, and 5%) as a replacement ratio from the weight of sand mixed with Ordinary Portland Cement (OPC). The findings of this research indicated the possibility of using aluminum waste material in certain limits where the compressive strength significantly reduced by increasing the percentage of als. The most interesting observation was to increase the volume of the mixture by increasing the ratio of als. According to the results, it is possible to use this type of cement mortar to produce lightweight structural members such as slabs, bricks, etc. Finally, the general formulation was proposed based on the regression analysis and experimental measurements to give a capture of the compressive strength of mortar under any variables alter (age of specimen and/or quantity of aluminum replacement).
Reference
Arimanwa, J.I., Onwuka, D.O., Arimanwa, M.C., Onwuka, U.S. (2012) Prediction of the compressive strength of aluminum waste-cement concrete using Scheffe's theory. Journal of Materials in Civil Engineering, 24(2): 177-183
ASTM International (2002) Standard test method for compressive strength of hydraulic cement mortar. ASTM C 109/C 109M-02
Bajare, D., Korjakins, A., Kazjonovs, J. (2011) Application of aluminium dross and glass waste for production of expanded clay aggregate. Civil Engineering, 11, 27-31
Brough, M. (2002) Aluminium lightens the environmental load. Vision - The newsletter of the Foresight and Link Initiative, No (4)
Central Organization for Standardization & Quality Control (COSQC) (1984) Portland cement. Baghdad, Iraqi Standard Specification (IQS), No. 5
Central Organization for Standardization & Quality Control (COSQC) (1984) Aggregates from natural sources for concrete and construction. Baghdad, Iraqi Standard Specification (IQS), No. 45
Chowdhury, S., Roy, S., Maniar, A.T., Suganya, O.M. (2014) Comparison of mechanical properties of mortar containing industrial byproduct. APCBEE Procedia, 9: 317-322
Dai, C. (2012) Development of aluminium dross-based material for engineering applications. Material Science and Engineering, M.Sc. Thesis, Worcester Polytechnic Institute
Elinwa, A.U., Mbadike, E. (2011) The use of aluminum waste for concrete production. Journal of Asian Architecture and Building Engineering, 10(1): 217-220
Hamead, A.A.A., Ahmed, S.S., Azzat, S.R.A., Abed, M.S., Hammod, G.K. (2020) Employing recycling materials for the fabrication of smart mortar. Materials Today: Proceedings, 20, 397-402
Hoornweg, D., Bhada-Tata, P. (2012) What a waste: A global review of solid waste management. u: Urban development series knowledge papers, Washington, DC: World Bank, March, No. 15, 116
Javali, S., Chandrashekar, A.R., Naganna, S.R., Manu, D.S., Hiremath, P., Preethi, H.G., Kumar, N. V. (2017) Eco-concrete for sustainability: utilizing aluminium dross and iron slag as partial replacement materials. Clean Technologies and Environmental Policy, 19(9): 2291-2304
Khater, H.M. (2019) Development and characterization of sustainable lightweight geopolymer composites. Cerâmica, 65(373): 153-161
Li, W., Huang, Z., Zu, T., Shi, C., Duan, W.H., Shah, S.P. (2016) Influence of nanolimestone on the hydration, mechanical strength, and autogenous shrinkage of ultrahigh-performance concrete. Journal of Materials in Civil Engineering, 28(1): 04015068
Li, W., Huang, Z., Cao, F., Sun, Z., Shah, S.P. (2015) Effects of nano-silica and nano-limestone on flowability and mechanical properties of ultra-high-performance concrete matrix. Construction and Building Materials, 95: 366-374
Mailar, G., Sreedhara, B.M., Manu, D.S., Hiremath, P., Jayakesh, K. (2016) Investigation of concrete produced using recycled aluminium dross for hot weather concreting conditions. Resource-Efficient Technologies, 2(2): 68-80
Mbadike, E.M., Osadere, N.N. (2014) Effect of incorporation of aluminium waste in concrete matrix using different mix ratio and water cement ratio. International Archive of Applied Sciences and Technology, 5(1), 47-54
Meng, T., Yu, Y., Qian, X., Zhan, S., Qian, K. (2012) Effect of nano-TiO2 on the mechanical properties of cement mortar. Construction and Building Materials, 29: 241-245
Minitab, Inc. (2010) Minitab 17 Statistical Software. State College, PA, Computer software, www.minitab.com
Morsy, M.S., Alsayed, S.H., Aqel, M. (2011) Hybrid effect of carbon nanotube and nano-clay on physico-mechanical properties of cement mortar. Construction and Building Materials, 25(1): 145-149
Nduka, D.O., Ede, A.N., Olofinnade, O.M., Ajao, A.M. (2020) Mechanical and water absorption properties of Normal Strength Concrete (NSC) containing Secondary Aluminum Dross (SAD). International Journal of Engineering Research in Africa, 47: 1-13, Trans Tech Publications Ltd
Nihad, N.A.Q., Numan, H.A. (2020) Behavior of sustainable reinforced concrete building containing waste plastic and fibers. IOP Conference Series: Materials Science and Engineering, 870: 012094, June
Okeyinka, O.M., Oloke, D.A., Khatib, J.M. (2015) A review on recycled use of solid wastes in building materials. International Journal of Civil and Environmental Engineering, 9, 12
Ozerkan, N.G., Maki, O.L., Anayeh, M.W., Tangen, S., Abdullah, A.M. (2014) The effect of aluminum dross on mechanical and corrosion properties of concrete. International Journal of Innovative Research in Science, Engineering and Technology, 3(3): 9912-9922
Pereira, D.A., de Aguiar, B., Castro, F., Almeida, M.F., Labrincha, J.A. (2000) Mechanical behaviour of Portland cement mortars with incorporation of Al-containing salt slags. Cement and Concrete Research, 30(7): 1131-1138
Rashad, A.M. (2013) Effects of ZnO2, ZrO2, Cu2O3, CuO, CaCO3, SF, FA, cement and geothermal silica waste nanoparticles on properties of cementitious materials: A short guide for Civil Engineer. Construction and Building Materials, 48, 1120-1133
Shinzato, M.C., Hypolito, R. (2005) Solid waste from aluminum recycling process: Characterization and reuse of its economically valuable constituents. Waste Management, 25(1): 37-46
Yaseen, M.H., Abbu, M., Numan, H.A. (2018) Influence of adding different amounts of polyethylene terephthalate on the mechanical properties of gypsum subjected to fire. International Journal of Civil Engineering and Technology, 9(10): 1721-1731
 

O članku

jezik rada: engleski
vrsta rada: izvorni naučni članak
DOI: 10.5937/jaes0-27113
primljen: 17.06.2020.
prihvaćen: 06.11.2020.
objavljen u SCIndeksu: 26.03.2021.
metod recenzije: dvostruko anoniman
Creative Commons License 4.0

Povezani članci

Nema povezanih članaka